how to make film strip projector ?


how to make film strip projector ?

Gather Your Materials – Get a slide projector, bulb, lens, a 7-inch cardboard tube, and some glue.


In this blog post, we’ll look at how to make an old-fashioned film strip projector. Film strip projectors were popular before home video systems, and many people still enjoy the nostalgia of using them for special occasions. You can easily recreate these classic projectors in your home with a few simple materials.

You’ll need a slide projector, bulb, lens, and a 7-inch cardboard tube. A slide projector is an essential part of the setup; it’s the device that allows light to pass through the film strip to create an image on a wall or screen. The bulb provides illumination while the lens ensures light passes through the film in a pattern. Finally, the cardboard tube acts as a channel for air to travel through so that any heat generated by the lamp can be dispersed safely away from it.

Once all your materials are gathered, connect your slide projector and bulb to an electrical outlet or extension cord. Next, insert one end of the cardboard tube over your projector’s lens. This will direct any heat away from both devices and keep them working correctly during use. Securely attach the line with some glue if necessary.

Now you’re ready to start projecting films! Place your film roll onto the feeder tray of your projector and carefully thread its leading edge into position. Once secure, turn on your lamp and adjust its brightness according to your preference by turning its knob clockwise or counterclockwise until it’s at an ideal level for viewing films – usually about 80-90 lumens is best for most movies in standard definition. Finally, adjust your lens’s focus to ensure that images appear crisp and clear on whatever surface you’re projecting onto (a white wall works best).

You now have everything you need to experience films just like they used to be experienced decades ago! And with minimal effort and equipment cost in making this DIY film strip projector, there’s no reason not to try it today!

Construct the Tunnel – Cut two pieces of cardboard to the same length that fits over the projector’s lens. Glue them together, so they form a tube. Ensure it can do the slides in place for projection and has enough room for air circulation inside.


Creating your film strip projector is a great way to add nostalgia to your home movie theater. With the right supplies and instructions, even the most novice DIYer can quickly create their film strip projector quickly.

The key to creating your film strip projector is constructing a tunnel, which helps guide and project the light from the bulb through the slides. This tunnel should be cut into two pieces of cardboard to fit over the projector’s lens. The two cardboard pieces should be the same length and width and glued together for an airtight seal. Ensure there is enough room for air circulation within the tunnel so that it won’t overheat and cause damage to either itself or any nearby equipment or furnishings.

To assemble your film strip projector, glue one end of both pieces of cardboard together using hot glue or another adhesive that will hold securely when heated. Allow enough space between each side so that you can easily slip in slides without having them jam up against each other as they go through the tunnel. The other end should have enough room to fit over the lens on your filmstrip projector. Once this is complete, set aside to dry.

Once dry, you must attach the tunnel to your projector lens. Begin by carefully removing any previous attachments from around it before connecting your new tube-like structure. Be sure not to use too much force when doing this, as it can break or loosen some of the internal parts of your projector if done incorrectly. Securely attach it with hot glue or another adhesive that will hold firmly when heated. Let cool before inserting slides inside and projecting them onto a wall or surface as regular film strips do.

Creating your film strip projector is satisfying yet straightforward once complete! All you need are some basic supplies such as cardboard boxes, glue, scissors, and a drill (if required) – plus a bit of patience – and you’re ready for some classic film projection fun! So gather these items today and start making yourself a unique piece of movie equipment!

Assemble the Lens Carrier – Cut another piece of cardboard into a circle shape slightly more significant than your lens. Glue it on one end of your tunnel and 2 small pieces of cardboard onto each side of your circle to serve as holders for your lens when you slide it in or out.


Creating your own film strip projector is an exciting project you can do at home. In this article, we’ll provide you with step-by-step instructions on how to assemble the lens carrier.

To begin, you will need a piece of cardboard to cut into a circle shape that is slightly bigger than your lens. Once missed, apply glue to one end of your tunnel and attach the cardboard circle. On either side of the process, affix two small pieces of cardboard that will be holders for when you slide in or out the lens.

Correctly assembling the lens carrier can be tricky and time-consuming if done incorrectly. That’s why you must have all your materials within reach before you begin construction so everything runs smoothly. Here are some additional tips on how to create a successful lens carrier:

• Make sure to measure twice and cut once

– measuring correctly ensures accuracy for the size of your cardboard circle and helps avoid mistakes during assembly.

• Don’t skimp on glue

– use enough for a long-lasting assemblage that will support your projector for years.
• Allow adequate drying time

– even if it takes longer than expected, give yourself some extra time for things to dry before beginning any other parts of construction.
• Take safety measures

– wear protective eyewear and gloves while handling sharp objects like scissors and knives during the cutting.

With these tips in mind, assembling the lens carrier should be a cinch! After completing this step, move on to the next phase of constructing your homemade film strip projector and enjoy the fruits of your labor!

Attach Slides and Film Strip – Place your film strip onto one end of your tunnel and attach it with glue or tape around its perimeter. Now you can add 2 or 3 slides to this end with glue or video too!


Making your film strip projector is an easy and cost-effective way to share memories with friends and family. With just a few supplies, you can quickly have a fun and nostalgic projector!

Before you begin, ensure you have all the necessary materials: a cardboard tube or tunnel, glue or tape, film strips, and slides. You will also need a light source, like a flashlight or lamp, to project the images.

To begin assembling your projector, start by taking the cardboard tube or tunnel and attaching the film strip to one end using glue or tape around its perimeter. Once the film strip is secure, add two or three slides to this same end of the tube using either glue or tape. Make sure that these slides face outward so that light can be projected through them when placed in front of your light source.

You can then place your light source at one end of the tube while covering the other with something dark (like a cloth). When ready, switch on your light source and point it at the slides near the other end of the tube. This should project an image from each slide onto whatever surface it is suggested at—and voila! You now have a working film strip projector!

Making a film strip projector with cardboard and other simple supplies is fun for children of all ages. Reliving classic memories through beautiful photographs or artwork captured on film strips and slides is also inexpensive. To start creating your projector today, gather all the necessary materials before beginning assembly!

Secure Your Projector Bulb – With everything else ready, you need to secure the bulb to light up your film reel when you turn on the projector.


The film strip projector is a classic piece of equipment that allows you to look at memories from a more nostalgic perspective. Even though most of us have moved on to digital formats, film strips still hold a special place in our hearts. However, the bulb is one of your projector’s most critical components. The bulb is responsible for illuminating and producing the light necessary to project your images onto the wall.

If you want your film strip projector to work correctly, ensure the bulb is appropriately secured before turning it on. This is crucial as an unsecured bulb can be dangerous and can lead to technical problems. Fortunately, securing a film strip projector’s bulb requires no special skills or tools – just some patience!

The first step in securing your projector’s bulb is ensuring it fits in its socket correctly. Once you are confident that the fit is snug and won’t move around when touched, you must use adhesive material, such as electrical tape or glue, to keep it in place. Be sure not to use too much adhesive, as this can also cause problems with overheating and short-circuiting over time, which could lead to damage or fire hazard.

Once you have applied enough adhesive and ensured that the bulb fits securely into its socket, plug in your projector and test it out by turning it on for a few seconds until you are sure everything is working properly. Now that your bulb has been secured correctly, insert your film reel into the projector and hit ‘play’ – enjoy!

These simple steps should help ensure that all parts of your film strip projector are secure so you can experience those treasured memories again without worrying about any safety risks or potential damages due to incorrect installation procedures. So if you want to relive those moments from yesteryear without worry, follow these steps – happy viewing!

6 Test It Out & Enjoy! – Turn on your projector and test if everything works properly before enjoying classic films!


Are you a fan of classic films? If so, it’s essential to ensure you have a reliable way to show them—and what better way than with a film strip projector? Creating your film strip projector is easier than ever, and all you need is the right equipment and a few simple steps. Here’s how to get started:

1. Gather Your Equipment

– The first step to making your film strip projector is gathering the necessary materials, which include a projector, film strips, and a spool for the film strips. Make sure each of these items is in good condition before beginning.

2. Set up the Projector

– Once you’ve gathered your supplies, it’s time to set up the projector. Place it on an even surface and ensure it is securely connected to power before turning it on. Also, make sure that the screen or wall you will be projecting onto is clear of any obstructions or furniture that could impede the clarity of projection.

3. Load the Film Strips

– Now it’s time to load the film strips into your projector. Start by threading one end of the film through the spool mechanism at the top of your projector, then slowly feed in until both ends are secure within the spool holder. Then carefully place each end of the film strip into its respective holder slot on either side at the back of your projector until they are secured.

4. Test It Out

– Before enjoying some classic films with your new setup, ensuring everything works properly is essential! Turn on your projector and test if images appear as expected; this will provide a smooth viewing experience later! Once everything seems normal, then you can proceed with enjoyment!

Making a good functioning film strip projector doesn’t have to be complicated or expensive—as long as you have all the necessary parts and follow these steps correctly, you can easily create one yourself! So go ahead—test it out and enjoy some classic films today!

Get the complete solution. ↓

The Ultimate Guide to Projector


Products from HaiDian

Recently Posted

Contact HaiDian

Simple Contact Form
Scroll to Top

Let's have a chat

Please fill in your request and we will be happy to help you!